Search Results

Visual movement of automotive components can induce a sense of poor quality and/or reliability to the customer. Many times this motion is likely to induce squeaks and rattles that further degrade customer opinion. For both of these reasons, it may be necessary to quantify the visual motion of certain components. This paper deals with a study in which the angular displacement from the observer to a passenger-side seat back was correlated to the subjective impression of seat back motion. Minutes Of Arc (MOAs) were found to correlate well to the perception of 17 subjects who evaluated the seat back motion of a seat mounted to a TEAM Cube in which road vibrations were played into a passenger seat and subjects were instructed that the evaluation surface was a “rough road” surface. This was confirmed for both the driver observing the unoccupied passenger seat from the side and a rear seat passenger viewing the unoccupied front seat from behind.

Air-conditioning (A/C) induced moan is a very commonly observed phenomenon in automotive refrigerant systems. Since most of the automotive A/C systems cycle ON/OFF four to six times every minute, the A/C induced moan is quite readily audible under engine idle and even while driving, especially under lower engine/vehicle speeds. It is not unusual for an A/C compressor to moan or not, on some vehicle/s under certain operating conditions. Most of the OEMs resolve or suppress the A/C moan potential to barely audible levels. However, under some unique and extreme operating conditions, A/C moan is quite readily induced and often results in customer complaints. This paper discusses A/C moan related root-causes, sources and paths of propagation. A systematic diagnostic test-procedure is also described to diagnose and develop the needed most cost-effective design-fixes. Finally, based on this case-study - some objective targets are recommended to suppress the A/C moan to acceptable levels.

In this paper, a nonlinear dynamic model for automotive cushion-human body combined structure is developed based on a nonlinear seat cushion model and a linear ISO human body model. Automotive seat cushions have shown to exhibit nonlinear characteristics. The nonlinear seat cushion model includes nonlinear stiffness and nonlinear damping terms. This model is verified by a series of tests conducted on sports car and luxury car seats. The transfer functions from the tests for human body sitting on an automotive seat changes with the vibration platform input magnitudes. This indicates that the combined structure possesses nonlinear characteristics. The nonlinear model is validated by the transfer functions from the test. The paper discusses the influence of the parameters of the nonlinear structure on the design of seat and assessment of human body comfort.

The paper presents a procedure for nonlinear model identification of automotive seat cushion structure. In this paper, two nonlinear models are presented. Tests show that the automotive seat cushion structure is a nonlinear system. The transfer functions obtained from the test data between the seat butt and the seat track show that the magnitude and frequency shift will be smaller as the input is increased. The models predict the transfer functions having the same trend as the results from the tests. The models are quite useful for the analysis other car structures and also provide guidance in the design of seat cushions.

In a continuing effort to include real-world emissions in regulatory testing, the USEPA has included air conditioning operation as part of the Supplemental Federal Test Procedure (SFTP). Known as the SC03, these tests require automobile manufacturers to construct and maintain expensive environmental chambers. However, the regulations make allowances for a simulation test, if one can be shown to demonstrate correlation with the SFTP results. We present the results from an experiment on a 1998 Ford sedan, which simulates the heat load of a full environmental chamber. Moreover, the test procedure is simpler and more cost effective. The process essentially involves heating the condenser of the air conditioning system by using the heat of the engine, rather than heating the entire vehicle. The results indicate that if the head pressure is used as a feedback signal to the radiator fan, the load generated by a full environmental chamber can be duplicated.

This paper describes a transient, thermodynamic, crank angle-based engine model in Modelica that can be used to simulate a range of advanced engine technologies. A single cylinder model is initially presented and described, along with its validation against steady-state dynamometer test data. Issues related to this single cylinder validation are discussed, including the appropriate conservation of hot residual gases under very early intake valve opening (IVO) conditions. From there, the extension from a single cylinder to a multi-cylinder V8 engine model is explained and simulation results are presented for a transient cylinder-deactivation scenario on a V8 engine.

An electromechanically driven valve train offers unprecedented flexibility to optimize engine operation for each speed load point individually. One of the main benefits is the increased fuel economy resulting from unthrottled operation. The absence of a restriction at the entrance of the intake manifold leads to wave propagation in the intake system and makes a direct measurement of air flow with a hot wire air meter unreliable. To deliver the right amount of fuel for a desired air-fuel ratio, we therefore need an open loop estimate of the air flow based on measureable or commanded signals or quantities. This paper investigates various expressions for air charge in camless engines based on quasi-static assumptions for heat transfer and pressure.

This paper introduces several requirements that have been created based on lessons learned at Ford Motor Company. This is not a collection of requirements already addressed by MISRA. These are requirements which address repeated or costly problems that have been observed at Ford Motor Company in their Electronic Body Modules. Real world examples of why they were needed will be highlighted as well as the principles used to create them and confirm compliance. Electronic Body Modules at Ford Motor Company usually control Interior Lighting, Exterior Lighting, Chime, Wipers, Power Mirrors, Power Seats and other features related to passenger comfort. These modules typically use less than 32 K of ROM and are written in C. While some modules are connected to a vehicle network, others are stand-alone.

Unlike the conventional seat belt system wherein the shoulder belt upper anchor is mounted on the vehicle body, Seat Integrated Restraint (SIR) system has the shoulder belt upper anchor mounted on the top of seat back frame. During a vehicle frontal impact, the stiffness of seat and that of the floor underneath the seat play a significant role in the performance of the restraint system in providing protection to the occupants. In this study the effect of the stiffness of seat and floor on the restraint system is investigated with other restraint parameters such as retractor load limit, fire time lag of dual stage inflator and air bag vent size. The stiffness of seat and floor is varied to determine the range of best occupant protection. This study attempts to establish feasible design targets of seat and floor stiffness for optimal restraint performance.

This paper describes an investigation into the fluid flow and heat transfer on the windshield as well the effect of the air discharge from the defroster vents on passenger comfort. The investigation is both experimental and computational. Full-scale tests are conducted on a current vehicle model using non-intrusive diagnostic methods. The results presented are from numerical simulations validated by experimental measurements. The numerical predictions compare well with the experimental measurements. The locations of maximum velocity and pressure, as well as width and length of re-circulation regions, are correctly predicted.

Several million pounds of S/MA glass reinforced resin has been successfully recovered from manufacturing offal and reject foamed / covered Instrument Panels (IP's) over the past ten years. ACI-WIPAG and Visteon recovered high quality S/MA resin, prepared blends with virgin resin and injection-molded IP substrates meeting OEM specifications. This “S/MA Resin Reclaim” process has been an economical and environmental success; minimized landfill volume, reduced landfill disposal costs, recovered a valuable resource, increased material utilization and reduced raw material costs. This paper reports on a new system and process to recover S/MA glass reinforced resin from manufacturing trim offal and reject IP's, blending and supplying OEM specification resin blends for molding instrument panel substrates. The system demonstrated economical recovery of an excellent quality “Reclaim” resin, blend consistency and uniformity for injection molding instrument panel substrates.

The history behind Polymer Class “A” Body Panels for automotive applications is very interesting. The driving factors behind these applications have not changed significantly over the past sixty years. Foremost among these factors is the need for corrosion and dent resistance. Beginning with Saturn in 1990, interest in polymer body panels grew and continues to grow up to the present day, with every new global application. Today, consumers and economic factors drive the industry trend towards plastic body panels. These include increased customization and fuel economy on the consumer side. Economic factors such as lower unit build quantities, reduced vehicle mass, investment cost, and tooling lead times influence material choice for industry. The highest possible performance, and fuel economy, at the lowest price have always been a goal.

A control strategy is presented to limit the rate of heat release by Diesel Particulate Filters (DPF) during regeneration reactions between oxygen and the collected soot. Heat release is managed by limiting the oxygen supplied to the DPF, which limits the rate of the regeneration reaction. Three actuators are used to control the amount of oxygen flowing in the exhaust system: an exhaust gas re-circulation (EGR) valve, an intake throttle (ITH), and a hydrocarbon injector located upstream of the DPF in the exhaust system. The EGR valve and ITH are low-bandwidth actuators that control slowly varying changes in oxygen flow, while the hydrocarbon injector is a high-bandwidth actuator that controls the corresponding fast changes in oxygen flow.

The parameterization of variable geometry turbochargers for mean-value modeling is typically based on compressor and turbine flow and efficiency maps provided by the supplier. At low turbocharger speeds, and hence low airflows, the heat exchange via the turbocharger housing affects the temperature-based measurements of the efficiencies. Therefore, the low-speed operating regime of the turbocharger is excluded from the supplied maps and mean-value models mainly rely on extrapolation into this region, which is regularly met in emission drive cycles, and hence of significance. This paper presents experimental data from a 2.0-liter turbocharged common-rail diesel engine. While the flow maps extend from the high-speed region in a natural way, the efficiency maps are severely affected by the heat transfer effect. It is argued that this effect should be included in the mean-value model.

Recently, several factors as advent of catalyst converter, tighter packages, calibration strategies with higher exhaust temperatures as well as corporate requirements concerning safety and passenger comfort have contributed to increase the necessity of applying concepts of heat transfer to vehicle development process, to make sure that heat rejection is properly managed in order to accomplish all these items. Traditionally, the method to verify these items has been physical tests in prototype vehicles. The most important advantage concerning this method is the accuracy of measurement results, since the prototype is usually close to the final product design level, being extremely representative. On the other hand, some disadvantages that can be pointed out in this method are concerning timing and costs involved in prototypes building process.

Today, Hybrid Electric Vehicles (HEVs) are synonymous to vehicles that offer a greater fuel economy and lower emissions when compared to their conventional production platforms. The development of an affordable hybrid technology faces challenges on several forefronts. Challenges include, but are not limited to, their technical content and development, corporate challenges, government regulations, program challenges, selecting technology partners and producing a hybrid vehicle that customers find fun to drive. As technologists, our goal is to ensure that the consumer understands that HEVs go that extra mile and provide far more than better fuel economy and lower emissions. HEVs are attractive and fun to drive because they offer multiple attributes and features to that consumers want. Hybrids offer all-wheel drive capability, traction control, regenerative braking, zero emissions, active air conditioning at vehicle stops, silent re-starts.

Increased cooling demands in Hybrid Electric Vehicles (HEVs), compactness of engine compartment, and the additional hardware under the hood make it challenging to provide an effective cooling system that has least impact on fuel economy, cabin comfort and cost. Typically HEVs tend to have a dedicated cooling system for the hybrid components due to the different coolant temperatures and coolant flow rates. The additional cooling system doubles the hardware, maintenance, cost, weight and affects vehicle fuel economy. In addition to the cooling hardware, there are several harnesses and electronics that need air cooling under the hood. This additional hardware causes airflow restriction affecting the convective heat transfer under the hood. It also affects the radiation heat transfer due to the proximity of hardware close to the major heat sources like the exhaust pipe.

A transient nonlinear Finite Element Analysis (FEA) method has been developed to simulate the inelastic deformation and estimate the thermo-mechanical fatigue life of cast iron and cast steel exhaust manifolds under dynamometer test conditions. The FEA uses transient heat transfer analysis to simulate the thermal loads on the manifold, and includes the fasteners, gasket and portion of the cylinder head. The analysis incorporates appropriate elastic-plastic and creep material models. It is shown that the creep deformation is the most single critical component of inelastic deformation for cast iron manifold ratcheting, gasket sealing, and crack initiation. The predicted transient temperature field and manifold deformation of the FEA model compares exceptionally well with two experimental tests for a high silicon-molybdenum exhaust manifold.

Maintaining adequate visibility at all times, through a vehicle windshield, is critical to the safe usage of the vehicle. The ability of the windshield defrosting and demisting system to quickly and completely melt ice on the outer windshield surface and remove mist formed on the inner surface is therefore of paramount importance. The objectives of this paper are to investigate the fluid flow and heat transfer on the windshield as well the effect of the air discharge from the defroster vents on passenger comfort. The results presented are from numerical simulations validated by experimental measurements both carried out a model and full-scale. The numerical predictions compare well with the experimental measurements at both scales. The effects of the defrosting and demisting air on occupants' comfort and safety are examined.

The penetration of rainwater through the heating ventilation and air conditioning system, HVAC, of a vehicle directly affects the provision of thermal comfort within the vehicle passenger compartment. The first element of a typical HVAC system, namely the cowl box is considered. The purpose of the airway from the cowl grille openings to the air filter, immediately before the blower, is to ensure proper water separation from the incoming air stream before entry onto the air filter and onwards into the rest of the HVAC system. This is achieved by ensuring standing water within the cowl is quickly drained and that water rain droplets or water flows from the windshield and body are separated from the air stream, hence minimising the effect on the total system volumetric flow rate. An experimental study is conducted to examine the effect of plane baffles on the airflow filed within a rectangular duct. A set of plane baffle plates is placed within the cowl duct.